Відео

Have a problem with rats. Apparently mesh needs to be placed in cab air exhaust in rear bumper. 2014 Forester. DID Subaru add a screen in later years?

Man, you're a stud. I've been going crazy for months now

Is there an example of the chatter?

My 19 Legacy has this "heat shield" style rattle at 30MPH under light throttle... I'm gonna check this out... thanks!!!

How about how to remove the seat and side covers to install Battery??

The 100a fuse is bolted both sides fuse box has to be taken apart to get to the bolts

my car is a Mazda protects 2003 e standard.. I started it and maybe I don't do anything please someone to help me... He just makes tacs and Tac the ralay that is at the passenger door

my car is a Mazda protects 2003 e standard.. I started it and maybe I don't do anything please someone to help me... He just makes tacs and Tac the ralay that is at the passenger door

my car is a Mazda protects 2003 e standard.. I started it and maybe I don't do anything please someone to help me... He just makes tacs and Tac the ralay that is at the passenger door

The noise is driving me insane. What kind of foam & where would u put the foam?

Nice. I made the mistake of putting on the front wheel first. Should have waited with that till I routed the fork cable and hoses and screwed on the plastic shields. And cross threaded a back rack bolt, should have untwisted the rack first to align holes. Other than that, the bike is a amazing piece of modern engineering. The fit and finish are first class.

Hello I’m having the exact same problem Mechanic couldn’t seem to find the problem I’m take your approach can you give me the names of the tools that your using I’m going to try to do it myself

Mine it crank but not staring it's mazda etude 1.6ie

$#it explained

i need wiring diagram

Thank you! My exact issue, and a quick easy diagnosis, I’m hot wired as well, until I find the replacement switch!

Why dont use powrr bamk

Goat vid thanks

Hi.can i know part no for starter?tq in advance

Thank god, just got my car back from Subaru after a week and they couldn’t even “duplicate” the noise. Don’t understand how cause it’s basically constant at that rpm. This was it

I have a 323f and it is exactly the same set up, I have a similar problem as you also with a 6 month old cheap starter, trying to replace it with a Bosch starter instead . Did the replacement work or did it turn out to be something else?.

Just ran into the same issue with my P5, the only question i have is where did you run the white wire off the solenoid??

How u did the wiring

Omg I wish I would of found this before I spent hours of my time and the poor people who had to deal with me over my phone number transferred totally my fault wrong zip code who knew I guess you ty so much

I just ordered mine and am pumped. Im a little concerned about weighing 270 lbs. Im 6ft and I wish I could say its muscle but it stopped being muscle at 220 when I got married 13 years ago and quit lifting weights 😅. Anyway, what do you weigh, if you don't mind me asking? Also, what adjustments should I make for my big self to ride this thing? Im pretty sure the max weight is like 330 lbs so I should be ok for the most part.

Thank you so much! I'll give you a thumbs up but I really wanna give you a hug! Hardwire for the win.

Your video is AWSOME!!! 🫡

Needed to change the starter on my '03 Protege and found your video. Thanks! Luckily I have smaller hands so it was easy getting to everything and was also able to remove the manifold support bracket.

On the fuel pump relay fuse the 2 things that you said looked burnt is on mine do i have a bad problem because i cant get it to start at all im just trying to get it to run again can you please help me figure it out thanks

The only thing Im not sure of, is where is the white wire on the relay going ? Black goes to the ground you mentioned. Red to the switch you installed, relay, and fuse box. Yellow and blue to the fuse box. Is the white another ground ? Appears to be hooked to that bolt on the strut tower.

Good stuff can't wait to receive mine

My brothers name was Benjamin he was a rider miss him so much tis the reason I made my channel good bike I have the blue one on layAway there's already a fella bad mou thing the kpx

Cool lil dude helping his cool azz pops💯💯💪💪💪💪

Where you get it from ?

Big thanks. Gonna tell my Subaru dealer tomorrow cause I can't do it myself....Curious to see what they say....Hope it's a fix cause it's just as you say...a chatter on passenger front accelerating tween 20 and 40 mph, then it stops. Gonna tell em to check the heat shields, too. Thanks again.

Thanks a lot, mate!!🙌🏻👏🏻👏🏻 I was absolutely lost with this sound/vibration! I fixed it with foam and replaced the old clips. No more noise at all! Fu****g legend!😃👍🏻

How did you get the seat off??

Thank you so much for this! My car has these weird rattles too.

Thanks for the video. Question, did the instructions include torque specifications for the various bolts?

I FIXED IT!!! check relay, all fuses, pump, I cleaned connectors, all good. Additional, take out the ECU (under plate, passenger side) to reinforce with soldering iron all motherboard´s connection. During check on, I removed relay, connecting COMs with a small wire, switch on, trying to get electricity to the pump. I heard a small explosion, luckily nothing happened... from there, car started normally.

Thanks for the shout-out. 👍

Good to know.👍 Also once you get some miles on it i would do a valve adjustment. My exhaust valve had zero clearance. That alone will cause poor idle as the engine will loose compression once it warms up.

Nice looking bike. If I get a dual sport, it would be this, but I have too many toys already. 600 Shadow and electric mountain bike.

Hey man I could really use your help is there anyway I can contact you?

Wow, finally fixed the noise that was annoying me so much, subaru legacy 2006. Thanks bunch

Helped me out with my 19’ crosstrek! Thanks much👊🏽

Oh man, this sound plagued my wife's car for the last like 10 years. This finally put an end to it once and for all!

Any insight on no spark ? I followed your video to trace the power back to the switch. Im bot sure if the alarm has anything to do with it though. Has to be the ignition switch, lock cylinder or alarm. Any way to bypass the alarm ? Problem is I bought it from a repo company and dont have original keys or FOB. So the lock can now be turned with just a blank. All acc comes on. No ignition though.

Can this work a Subaru Legacy 2011? Cuz I have the same noise !

I recently had problems with my Mazda protege hatchback not cranking. I replaced the 100A fuse and got a new battery and new connectors, problem solved!